X
 
  • Filter
  • الوقت
  • عرض
مسح الكل
مشاركات جديدة

    Font Size
    #1
    Canadian Wood Council WoodWorks Design Office USA Edition v11.1 SR-1


    Code:
    With WoodWorks Sizer, you can size beams, joists, columns and wall studs to meet the 2015 National Design Specification (NDS) for Wood Construction.
    
        Specify dead, live, snow and wind loads
        Automatically pattern loads
        Generate a materials take-off summary based on your design
        Design for point, line, area, triangular, and trapezoidal loads simultaneously
        Automatically check all load combinations as per IBC 2015, ASCE 7-10
        Analyze the critical load cases for reactions at supports, shear, bending, and deflection
        Generate detailed analysis reports and diagrams
        Generate a list of acceptable sections for dimension lumber, heavy timbers, glulam, LVL, or I-joists
        Use the Materials Database editor to customize the software to your needs
    
    Design Entire Structures – Concept Mode
    
        Configure and design a complete structure in plan
        Do preliminary designs of structures considering gravity loads using the graphical design and analysis work area
        Perform multi-storey gravity load analysis – sizing all structural members and reporting the reactions at the base
        Export elements from Concept Mode for further analysis into either Beam Mode or Column Mode
    
    Design Beams – Beam Mode
    
        Design individual wood bending members
        Use Beam Mode to verify the design of critical bending members
        Generate deflection, shear and bending moment diagrams for any beam or joist in your project
        Design single or multi-span beams and joists with or without cantilevers
        Design beams for gravity and uplift loads
        Specify full, clear or design span
        Design supporting members for bearing
        Design Beams with end and interior notches
    
    Design Columns – Column Mode
    
        Design individual wood columns, walls, and beam-columns
        Use Column Mode to verify the design of critical compression members
        Design columns and wall studs to resist both axial and lateral loads
        Generate deflection, shear and bending moment diagrams for a single column or wall stud
        Check wall bottom plate for bearing
    
    Shearwalls
    
    With WoodWorks Shearwalls, you can perform complete shearwall design and lateral load analysis.
    
        Design shearwalls for multi-storey and irregularly shaped buildings
        Determine hold-down and drag-strut forces and display them graphically
        Design shearwalls with or without hold-downs
        Generate an elevation view to show loads and forces on each shearwall
        Assign loads to shearlines following a flexible or rigid diaphragm analysis
        Import Adobe PDF and CAD (.wmf) files to establish the building footprint
        Model wood structures up to six stories
        Specify openings in shearwalls such as windows and doors
        Model roof shapes, including hips, valleys, gables, and overhangs
        Quickly assess the locations of high aspect ratio segments in a structure
    
    Wind Load Generation
    
        Generate wind pressure and resulting lateral loads as per ASCE 7-10
        Input specific site information, including wind speed up over a hill
        Manually input lateral loads or modify wind loads that were automatically generated
        Report shearwall material designs for all wind load cases
        Check the capacity of wall sheathing and nailing to resist wind suction (components and cladding loads)
        Check shearwalls for wind serviceability deflection and story drift
    
    Seismic Load Generation
    
        Generate seismic loads as per the IBC 2015 (ASCE 7-10)
        Input site-specific seismic information
        Manually input lateral loads or modify seismic loads that were automatically generated
        Report shearwall material designs for all seismic load cases
    
    Connections
    
    With WoodWorks Connections, you can design new connections or check the capacity of existing ones.
    
        Produce fully dimensioned, CAD-quality drawings
        Generate a material list for fasteners and steel plates
        Run designs using lag screws, wood screws, bolts, nails, shear plates or top-mount hangers
    
    Post & Beam Connections
    
        Design connectors for beam-to-beam, beam-to-column, and column-to-foundation connections
        Allows output of beam-to- beam connections as .dxf files for use in AutoCAD
    
    Lapped Shear Connections
    
        Design single or double shear connections for wood-to-wood, wood-to-steel, and wood-to-concrete configurations
    Canadian Wood Council WoodWorks Design Office USA Edition v11.1 SR-1


    Size: 106 MB

    Download
    *

    Font Size
    #2
    تسلم ايدك الغالي بومحمد


    تحياتي
    تعليق

      Font Size
      #3
      Thanks a lot I was looking for it (y)
      تعليق

        Font Size
        #4
        جزاك الله خيرا
        تعليق

          Font Size
          #5
          looks like your an avid fan of lavteam. nice!!
          تعليق

            Font Size
            #6
            Originally posted by Inhinyero1 *
            looks like your an avid fan of lavteam. nice!!
            Most engineering programs are published for all sites from lavtem, and we keep their logo and info file without any change, so, all credit goes to lavtem Of course


            تعليق

              Font Size
              #7
              Thanks a lot man, i was looking for it. Good well
              تعليق

                Font Size
                #8
                Great Job. Do you have the Canadian Version. Much Appreciated
                تعليق

                  Font Size
                  #9
                  Win32/Packed.Themida.HFL [Threat Name]

                  تعليق
                  Working...
                  X